RJ45 Pinout & T568A vs T568B Color Code Visualizer

Interactive RJ45 Ethernet pinout and wire order visualizer. Select T568A, T568B, or Crossover wiring standards to inspect pin-by-pin color codes, pair numbers, PoE wire pairs, and Keystone punchdown sequences.

TIA/EIA-568-B
Universal commercial networking standard in the United States. Used in >95% of patch cables.

Interactive Cable Type & Crossover Checker

Standard Straight-Through Ethernet Cable (T568B)

Both ends are crimped to T568B. This is a standard straight-through patch cable certified for 100M, 1GbE, 2.5GbE, 5GbE, and 10GBASE-T links connecting computers, switches, routers, access points, and IP cameras.

T568A vs T568B: What Is the Difference?

The physical difference between T568A and T568B is simply the swap of two wire pairs: Pair 2 (Orange) and Pair 3 (Green). Pins 4 and 5 (Pair 1 Blue) and Pins 7 and 8 (Pair 4 Brown) remain in the exact same positions on both standards. There is zero performance difference in speed, latency, SNR, or bandwidth between T568A and T568B—both achieve identical 10-Gigabit speeds across Cat6 and Cat6a cabling.

Why T568B Is the Dominant Standard in the United States

Although the TIA/EIA standard originally recommended T568A for backward compatibility with 2-line AT&T telephone jacks (USOC), the networking industry overwhelmingly adopted T568B. Today, over 95% of pre-molded commercial patch cables sold in North America follow T568B. While you can use either standard in your home or office, you must standardize on one standard across the entire building. Terminating one jack with T568A and the opposing patch panel port with T568B accidentally creates a crossover cable.

Gigabit (1000BASE-T) vs Fast Ethernet (100BASE-TX) Pin Utilization

Legacy Fast Ethernet (10/100 Mbps) only used 2 pairs (4 wires): Pins 1 & 2 for transmission (Tx) and Pins 3 & 6 for receiving (Rx). Pins 4, 5, 7, and 8 carried zero network data. In contrast, Gigabit Ethernet (1000BASE-T), 2.5GbE, 5GbE, and 10GBASE-T require all 4 pairs (8 wires) operating simultaneously in full duplex bidirectional mode (hybrid hybrid cancellation). If even one conductor in Pins 4, 5, 7, or 8 is severed or improperly crimped, Gigabit switches will automatically negotiate down to 100 Mbps Fast Ethernet.

PoE (Power over Ethernet) Wire Pinout Mapping

Power over Ethernet (PoE) delivers DC current across the same 8P8C modular connector:

  • Alternative A (Mode A): Injects power on data pairs 1/2 and 3/6 using common-mode voltage. Supported by both 10/100 and Gigabit switches.
  • Alternative B (Mode B): Injects positive power on Pins 4 & 5 (Blue) and negative return on Pins 7 & 8 (Brown). In 10/100 networks, these were 'spare' pairs.
  • 4-Pair PoE (802.3bt Type 3 & Type 4): Modern 60W and 90W PoE switches inject power simultaneously across all 4 twisted pairs (Pins 1 through 8).

Keystone Jack Punchdown Sequence for Clean 10GbE Installs

When terminating in-wall Cat6 or Cat6a cables into RJ45 Keystone jacks, follow the color diagram stamped on the side of the jack plastic body. Look for the row labeled 'B' (for T568B). The critical rule for achieving 10GbE certification is to keep wire pair untwisting under 0.5 inches (12 mm) right up to the punchdown IDC teeth. Excessive untwisting degrades Near-End Crosstalk (NEXT) and causes packet drops or CRC errors under high link saturation.